Crimp Tool Positioners, Turrets & Locators

Crimp Tool Positioners are parts of a Crimping tool designed to adapt the tool frame to a particular application. Available in a wide selection of sizes and shapes locators guarantee versatility of every crimping tool. The data plate on each positioner designates which contacts the positioner accommodates for its wire size and indicates selector position. The positioners are easy to remove and replace when different connector size is required.


How easy crimping tools and positioners, turrets and locators are to use?


They are very easy to use, insert the contact pin into the hole of the crimp tool, load the wire into the contact pin, make sure it’s fully seated then and squeeze until the cycle finishes then finally check that you have a secure crimp.


How do you maintain the product?


There is very little maintenance required for this tool, keep the indenter tips free of debris and dirt.


The Importance of a High-Quality Crimp


When a crimping tool is used on a terminal, two crimps take place at the same time. One is the electrical connection between the conductor and the terminal. The other is the insulation crimp which provides strain relief against vibration and tension.The electrical connection must be gas-tight without any voids between the wire strands and the terminal. If there are any voids present, then corrosion can occur causing resistance and excessive heat which damages the electrical connection. Using a good quality crimping tool will ensure that a full, gas-tight crimp is produced preventing future deterioration of the electrical connection and insulation breakage.


...
Read more Read less

Filters

Viewing 41 - 60 of 101 products
Results per page
Description Price Type Series Number of Contacts Series Number
RS Stock No. 876-2056
Mfr. Part No.169403
$52.91
Each
units
Locator AMP - -
RS Stock No. 865-8385
Mfr. Part No.09990000507
BrandHARTING
$378.28
Each
units
Positioner - - -
RS Stock No. 329-9843
Mfr. Part No.09990000304
BrandHARTING
$79.53
Each
units
Crimping Head - - -
RS Stock No. 876-1980
Mfr. Part No.4-539785-8
$96.03
Each
units
Locator CERTI-CRIMP II - -
RS Stock No. 173-9643
Mfr. Part No.63819-4375
BrandMolex
$89.60
Each
units
Locator 207128 - 63819
RS Stock No. 174-3156
Mfr. Part No.5-456406-6
$245.98
Each
units
Wire Crimper - - -
RS Stock No. 173-9630
Mfr. Part No.63819-0175
BrandMolex
$89.60
Each
units
Locator 207128 - 63819
RS Stock No. 173-9631
Mfr. Part No.63825-8175
BrandMolex
$98.77
Each
units
Locator 207128 - 63825
RS Stock No. 173-9644
Mfr. Part No.63819-4475
BrandMolex
$74.07
Each
units
Locator 207128 - 63819
RS Stock No. 721-1443
Mfr. Part No.1208474
$81.27
Each
units
Assembly Tool SACC BIT M8-D12 - -
RS Stock No. 174-3166
Mfr. Part No.722979-6
$1,455.48
Each
units
Wire Crimper - - -
RS Stock No. 174-3157
Mfr. Part No.1-456403-6
$245.98
Each
units
Wire Crimper - - -
RS Stock No. 876-2359
Mfr. Part No.525441-4
$598.25
Each
units
Plug Gauge - - -
RS Stock No. 174-3158
Mfr. Part No.690459-1
$456.53
Each
units
Shear Holder - - -
RS Stock No. 173-9645
Mfr. Part No.63810-0104
BrandMolex
$20.46
Each
units
Spring 207129 - 63810
RS Stock No. 174-3164
Mfr. Part No.1-1729372-0
$489.81
Each
units
Anvil - - -
RS Stock No. 174-3162
Mfr. Part No.690587-1
$283.48
Each
units
Wire Crimper - - -
RS Stock No. 173-9632
Mfr. Part No.63827-1475
BrandMolex
$81.49
Each
units
Locator 207128 - 63827
RS Stock No. 173-9634
Mfr. Part No.63819-1175
BrandMolex
$98.77
Each
units
Locator 207128 - 63819
RS Stock No. 175-6027
Mfr. Part No.JBX1OUTLS07
BrandSouriau
$900.89
Each
units
Locator JBX - -
Related Products
8 - Indent Crimp Tool An 8 indent ...
Description:
8 - Indent Crimp Tool An 8 indent crimp tool designed around MIL-C-22520/2 (settings 3 upwards) The correct positioner is located in the tool to act as a stop for the crimp terminal. This ensures the crimp barrel is at ...
Place the tool into the cavity from front ...
Description:
Place the tool into the cavity from front face of the insulator Push on the handle Remove the contact by pulling on it
Tooling Support crimp tools and positioners (not illustrated), ...
Description:
Tooling Support crimp tools and positioners (not illustrated), are available and can be selected from the table according to contact current rating The 400 series provides a compact secure connection where a high level of environmental sealing is required. For ...
Accessories Stainless steel Compatible with MIL-STD 83513 interfaces ...
Description:
Accessories Stainless steel Compatible with MIL-STD 83513 interfaces Note Crimp tool manufactured by Glenair Lightweight design and very high density, micro Comp® is an alternative to HD DSUB with superior characteristics,A flexible alternative to MIL-STD 83513 connectors. Stainless steel Compatible ...