LeCroy HVFO103 Oscilloscope Probe, Probe Type: High Voltage 60MHz 35kV

Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
COO (Country of Origin): US
Product Details

Teledyne LeCroy Oscilloscope Probe

The Teledyne LeCroy oscilloscope probe is affordable and optimally designed for measurement of small signals floating on an HV bus in power electronics designs or for EMC, EFT, ESD and RF immunity testing sensor monitoring. It far surpasses the measurement capabilities and signals fidelity of both conventional HV differential probes and acquisition systems that rely on galvanic high voltage isolation. Also, it mitigates the need to rely on dangerous test set-ups that require floating the oscilloscope and probe.
Spare HVFO103-XMITTER amplifier/modulating transmitters are available. Having a spare permits constant operation - charge one while the other is being used.
Supplied with:
1 x Amplifier/modulating transmitter
1 x demodulating receiver
1.1-metre fibre optic cable
1 x USB charging cable and 1 x micro gripper set

Features and Benefits

Bandwidth is DC to 60MHz 1GHz (–3dB)
Probes selectable tips from ±1V to ±40V
Common mode voltage range is ±35kV (DC+Peak AC)
Input impedance is 1Mohm ll34pF each side to ground
Maximum input voltage to earth is ±35kV (DC+Peak AC)
Non-destructive max. input voltage is 5 times the operating voltage rating
Offset capability determined by oscilloscope offset available in a given gain (V/div) setting after accounting for total probe attenuation
CMRR (typical) is 140dB (100Hz), 120dB (to 1MHz), 85dB (to 10MHz), 60dB (to 60MHz)
Ambient operating temperature ranges between 0°C and 50°C
It also reduces noise, distortion, ringing, overshoots, and transients on the measured signal.
Reduced DUT loading, better pulse response compared to conventional HV differential
Eliminates need to float the oscilloscope ProBus-compatible with many Teledyne LeCroy oscilloscopes


Upper-side gate drive signal measurements
Floating control signal or sensor voltage measurements
EMC, EFT, ESD and RF immunity testing and system optimization
Small signal measurements with the high common-mode voltage


Low Voltage Directive 2014/35/EU(IEC/EN 61010-031:2015
EMC Directive 2014/30/EU (IEC/EN 61326-1:2013)
UL 61010-031 Listed
CAN/CSA - C22.2 No. 61010-031-07 Listed

Attribute Value
Probe Type High Voltage
Bandwidth 60MHz
Maximum Common Mode Input Voltage 35kV
Connector Type USB
Model Number p HVFO103
Number of Probes 1
Series HVFO
Rise Time 7.5ns
2 In stock for delivery within 7 working day(s) (Global Stock)
Price (ex. GST) Each
$ 8,566.81
(exc. GST)
$ 9,423.49
(inc. GST)
Per unit
1 +
Related Products
Pico 200/2000A AC/DC Current Probe, D9 Connector The ...
Pico 200/2000A AC/DC Current Probe, D9 Connector The TA301 is a high-bandwidth, high-current probe fitted with a D9 connector specifically designed to work with the Pico Scope 4444 differential oscilloscope The probe is automatically sensed by the Pico Scope 4444 ...
The Tektronix 120AC current oscilloscope probe offers accurate ...
The Tektronix 120AC current oscilloscope probe offers accurate current measurements over a wide range of frequencies It allows current measurements without breaking the circuit by clipping onto the current-carrying conductor. The shielded probe head is not grounded when the slides ...
The Tektronix AC/DC current measurement probe is a ...
The Tektronix AC/DC current measurement probe is a highly advanced current measurement system created for the contemporary current measurement needs When connected to Tektronix oscilloscopes with TEKPROBE Level II, Tek Connect (w/ TCA-BNC), or TekVPI (w/ TPA-BNC) interfaces, current measurements ...
Pico 600 A AC/DC Current Probe TA019, BNC ...
Pico 600 A AC/DC Current Probe TA019, BNC Connector Pico TA019 current probe can measure AC and DC currents up to 60A Two current ranges controlled by selector switch Low–battery indicator Zero offset button Output connectors BNC with screened lead ...