STMicroelectronics L298P, Brushed Dual Full Bridge Motor Driver, 46 V 4A 20-Pin, PowerSO

Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

L298 Dual Full Bridge Motor Driver

ST Microelectronics presents its L298 dual full bridge driver series. The L298 series from ST is an integrated high voltage, high current dual full bridge driver. These devices are specially designed to accept standard TTL logic and drive inductive loads in Relays, Solenoids, DC and Stepper Motors. Featured are two enable inputs that allow the L298 to be enabled or disabled independently of the input signals. The emitters of the lower transistors of each bridge are connected together, the corresponding external terminal can be used to connect an external sensing resistor. In addition, a supply input is provided so that the logic works at a lower voltage.

Features

  • Operating supply voltage up to 46 V

  • Total DC current of up to 4 A

  • Low saturation voltage

  • Over-temperature protection

  • Logical "0" input voltage up to 1.5 V (high noise immunity)

What are Motor Driver IC's?

Motor Driver ICs are current amplifiers and are an essential component of motor interfacing. The motor driver integrated circuit chip acts as the interface between a microprocessor or microcontroller, and a motor. As microprocessors tend to operate at lower currents, and motors at higher, motor driver ICs are needed to supply current to the motor as needed. The RS Components range of Motor Driver ICs includes models from leading brands, in various types and configurations to support your design needs.

Motor Controllers & Drivers, STMicroelectronics

Specifications
Attribute Value
Motor Type Brushed DC
Output Configuration Dual Full Bridge
Maximum IGBT Collector Current 4A
Maximum Collector Emitter Voltage 46 V
Mounting Type Surface Mount
Package Type PowerSO
Maximum Operating Supply Voltage 46 V
Pin Count 20
Minimum Operating Supply Voltage 4.8 V
Inverter Power Rating 25W
Width 11.1mm
Maximum Operating Temperature +130 °C
Length 16mm
Height 3.6mm
Dimensions 16 x 11.1 x 3.6mm
Minimum Operating Temperature -25 °C
16 : Next working day (AU stock)
132 : 5 working days (Global stock)
Price (ex. GST) Each
$ 9.42
(exc. GST)
$ 10.36
(inc. GST)
units
Per unit
1 - 9
$9.42
10 - 49
$8.94
50 - 149
$8.67
150 - 499
$8.31
500 +
$7.70
Packaging Options:
Related Products
Allegro ICs for half- and full-bridge drives (brush ...
Description:
Allegro ICs for half- and full-bridge drives (brush motor, dc motor driver, dc brushed motor, brush dc motor)Brush DC motors are the most widely used drivers due to their low cost and simple drive control options Typical brush DC motors ...
BD62222HFP is full bridge driver for brush motor ...
Description:
BD62222HFP is full bridge driver for brush motor applications This IC can operate at a wide range of power-supply voltages (from 6V to 27V), supporting output currents of up to 2.5A. MOS transistors in the output stage allow for PWM ...
Description:
The STSPIN240 is a dual brush DC motor driver integrating a low RDS(ON) power stage in a small QFN 3 x 3 mm packageBoth the full-bridges implement an independent PWM current controller with fixed OFF time.The device is designed to ...
SLLIMM™ Intelligent Power Modules, STMicroelectronics STMicroelectronics has extended ...
Description:
SLLIMM™ Intelligent Power Modules, STMicroelectronics STMicroelectronics has extended its offering of IGBT intelligent power modules with the introduction of the second series of SLLIMM intelligent power modules Thanks to the optimal trade-off between conduction and switching energy, combined with outstanding ...