Adafruit 2454, DPI TFT Kippah Interface Board for Raspberry Pi

Technical data sheets
Legislation and Compliance
RoHS Certificate of Compliance
Product Details

Adafruit DPI TFT Kippah for Raspberry Pi

This Adafruit DPI Kippah has a TFT panel which is connected to a Raspberry Pi without the use of on HDMI decoder. With a little software configuration, what normally would go out the HDMI port, now will come up on a nice little flat screen.

What is it compatible with?

Raspberry Pi B+, A+, Pi 2, Pi 3 or Zero

A little bit about the screen

This Kippah has not got a touch screen, however, you will get a sleek ultra-fast 18-bit colour display with optional touch support. When tested the results showed that this can be used with 5’’and 7’’ displays at 800x480. Kippah screen is what is called ’native’. What does that mean? It means that it gets all the graphics acceleration capabilities as well as immediate refresh which you would normally get from an HDMI display.

What is the advantage of Kippah?

This add on board uses almost every pin available on the Raspberry Pi. Pins are hardcoded, so they cannot be moved or rearranged. UART RX/TX pins (no console cable) and standard user I2Cpins are not included. Same as the EEPROM I2C pins, or hardware SPI pins.
Pins used:
• GPIO 2 through 21 inclusive
• #22, #23, #24, #25, #26 and #27
• USB port
Display replaces the HDMI/NTSC output, therefore DPI HAT and HDMI won’t be working simultaneously and you won’t be able to switch between the two.

Specifications:

This single-display module is suitable for use in Multimedia Player products. The LCD adopts one backlight with High brightness 12-lamps white LED.

LCD:
• Amorphous-TFT 5.0 inch display, transmissive, normally white type
• 800(RGB) x 480 dots Matrix
• Narrow-contact ledge technique
• LCD Driver IC: HX8264D x1 & HX8664B x1
• RGB interface
• Video signal interface: Parallel RGB or serial

Not included: TFT display, USB micro-B cable, FPC Extension cable, bent wire stand and Raspberry Pi.

Specifications
Attribute Value
Kit Classification Interface Board
For Use With Raspberry Pi
Kit Name DPI TFT Kippah
2 : Next working day (AU stock)
9 : 5 working days (Global stock)
Price (ex. GST) Each
$ 22.02
(exc. GST)
$ 24.22
(inc. GST)
units
Per unit
1 +
$22.02
Related Products
This pHAT provides a super affordable high-quality DAC ...
Description:
This pHAT provides a super affordable high-quality DAC for your Raspberry Pi It pumps out 24-bits at 192KHz from the Raspberry Pi's I2S interface on its 2x20 pin GPIO header. Use pHAT DAC to build a tiny, lush-sounding streaming music ...
The Microchip LAN9252 PICtail is an add-on board ...
Description:
The Microchip LAN9252 PICtail is an add-on board for investigating and developing the LAN9252 EtherCAT® Slave Controller with the Microchip Explorer 16 Development Platform The board supports both HBI PDI and SPI/SQI configurations via a simple selector switch.The LAN9252 is ...
Just Boom Amp HAT is a high-quality audio ...
Description:
Just Boom Amp HAT is a high-quality audio amplifier with digital to analogue converter designed specifically for the Raspberry Pi (models: A+, B+, 2B or 3B) No external sound cards or DACs are required. Easy to install and use, stack ...
An Optical Pulse Sensor Evaluation board from ROHM ...
Description:
An Optical Pulse Sensor Evaluation board from ROHM intended for use with the Arduino Sensor Shield Evaluation Kit, RS 125-0453 The modular board includes the BH1790GLC optical sensor IC and suitable green LEDs allowing human pulse detection via finger contact. ...